Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of KELON A FR H2 CETG/300-V0 - PA66-(GF+MX) - LATI Industria Termoplastici S.p.A.

Material Data Center offers the following functions for KELON A FR H2 CETG/300-V0:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Kelon A datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Caratteristiche Fisiche - Proprietà Meccaniche - Proprietà Termiche - Proprietà Elettriche - Altre Proprietà - Raccomandazione de Processabilità Stampaggio ad Iniezione
Any use of this information falls under the rules of our disclaimer.
Caratteristiche FisicheValoreUnitáNorma del test
ISO Data
Ritiro di stampaggio, parallelo 0.6 % ISO 294-4, 2577
Ritiro di stampaggio, perpendicolare 0.7 % ISO 294-4, 2577
Proprietà MeccanicheValoreUnitáNorma del test
ISO Data
Modulo a trazione 10000 MPa ISO 527
Carico unitario a rottura 80 MPa ISO 527
Deformazione a rottura 1.6 % ISO 527
Resistenza all'urto Charpy, +23°C 20 kJ/m² ISO 179/1eU
Resist. urto Charpy con intaglio, +23°C 2 kJ/m² ISO 179/1eA
Proprietà TermicheValoreUnitáNorma del test
ISO Data
Temp.di inflessione sotto carico, 1.80 MPa 220 °C ISO 75-1/-2
Temp.di inflessione sotto carico, 0.45 MPa 240 °C ISO 75-1/-2
Temp.di rammollimento Vicat, B 235 °C ISO 306
Coeff.di dilatazione termica lin., parallelo 30 E-6/K ISO 11359-1/-2
Glow Wire Flammability Index (GWFI) 960 °C IEC 60695-2-12
GWFI - thickness tested (1) 1 mm -
Glow Wire Flammability Index (GWFI) 960 °C IEC 60695-2-12
GWFI - thickness tested (2) 2 mm -
Glow Wire Ignition Temperature (GWIT) 850 °C IEC 60695-2-13
GWIT - thickness tested (1) 1 mm -
Glow Wire Ignition Temperature (GWIT) 775 °C IEC 60695-2-13
GWIT - thickness tested (2) 2 mm -
ASTM Data
UL 94 combustibilitá V-0 - UL 94
Spessore testati 0.75 mm -
Indice limite di ossigeno 36 % ASTM D 2863
Proprietà ElettricheValoreUnitáNorma del test
ISO Data
Res. Alle correnti striscianti superficiali 400 - IEC 60112
ASTM Data
Resistenza superficiale 1E12 Ohm ASTM D 257
Altre ProprietàValoreUnitáNorma del test
Massa volumica 1610 kg/m³ ISO 1183
Raccomandazione de Processabilità Stampaggio ad IniezioneValoreUnitáNorma del test
Pre-essiccamento - Temperatura 90 - 100 °C -
Pre-essiccamento - Tempo 3 h -
Temperatura di fusione 270 - 290 °C -
Temperatura dello stampo 70 - 100 °C -
Caratteristiche
Processabilità e Forma di Forni
Stampaggio ad Iniezione
Additivi
Agente ritardante di fiamma
Caratteristiche speciali
Stabilizzato o stabile al calore
Disponibilità geografica
Europa
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.